Preamplifier in the context of Power amplifier

An amplifier, electronic amplifier or (informally) amp is an electronic device that can increase the magnitude of a signal (a time-varying voltage or current). It is a two-port electronic circuit that uses electric power from a power supply to increase the amplitude (magnitude of the voltage or current) of a signal applied to its input terminals, producing a proportionally greater amplitude signal at its output. The amount of amplification provided by an amplifier is measured by its gain: the ratio of output voltage, current, or power to input. An amplifier is defined as a circuit that has a power gain greater than one.

An amplifier can be either a separate piece of equipment or an electrical circuit contained within another device. Amplification is fundamental to modern electronics, and amplifiers are widely used in almost all electronic equipment. Amplifiers can be categorized in different ways. One is by the frequency of the electronic signal being amplified. For example, audio amplifiers amplify signals of less than 20 kHz, radio frequency (RF) amplifiers amplify frequencies in the range between 20 kHz and 300 GHz, and servo amplifiers and instrumentation amplifiers may work with very low frequencies down to direct current. Amplifiers can also be categorized by their physical placement in the signal chain; a preamplifier may precede other signal processing stages, for example, while a power amplifier is usually used after other amplifier stages to provide enough output power for the final use of the signal. The first practical electrical device which could amplify was the triode vacuum tube, invented in 1906 by Lee de Forest, which led to the first amplifiers around 1912. Today most amplifiers use transistors.

A microphone, colloquially called a mic (/maɪk/), or mike, is a transducer that converts sound into an electrical signal. Microphones are used in telecommunication, sound recording, broadcasting, and consumer electronics, including telephones, hearing aids, and mobile devices.

Several types of microphone are used today, which employ different methods to convert the air pressure variations of a sound wave to an electrical signal. The most common are the dynamic microphone, which uses a coil of wire suspended in a magnetic field; the condenser microphone, which uses the vibrating diaphragm as a capacitor plate; and the contact microphone, which uses a crystal of piezoelectric material. Microphones typically need to be connected to a preamplifier before the signal can be recorded or reproduced.

An instrument amplifier is an electronic amplifier that converts the often barely audible or purely electronic signal of a musical instrument into a larger electronic signal to feed to a loudspeaker. An instrument amplifier is used with musical instruments such as an electric guitar, an electric bass, electric organ, electric piano, synthesizers and drum machine to convert the signal from the pickup (with guitars and other string instruments and some keyboards) or other sound source (e.g, a synthesizer's signal) into an electronic signal that has enough power, produced by a power amplifier, to drive one or more loudspeaker that can be heard by the performers and audience.

Combination (combo) amplifiers include a preamplifier, a power amplifier, tone controls, and one or more speakers in a cabinet, a housing or box usually made of wood. Instrument amplifiers for some instruments are also available without an internal speaker; these amplifiers, called heads, must plug into one or more separate speaker cabinets. Instrument amplifiers also have features that let the performer modify the signal's tone, such as changing the equalization (adjusting bass and treble tone) or adding electronic effects such as intentional distortion or overdrive, reverb or chorus effect.

A guitar amplifier (or amp) is an electronic device or system that strengthens the electrical signal from a pickup on an electric guitar, bass guitar, or acoustic guitar so that it can produce sound through one or more loudspeakers, which are typically housed in a wooden cabinet. A guitar amplifier may be a standalone wood or metal cabinet that contains only the power amplifier (and preamplifier) circuits, requiring the use of a separate speaker cabinet–or it may be a combo amplifier, which contains both the amplifier and one or more speakers in a wooden cabinet. There is a wide range of sizes and power ratings for guitar amplifiers, from small, lightweight practice amplifiers with a single 6-inch speaker and a 10-watt amp to heavy combo amps with four 10-inch or four 12-inch speakers and a 100-watt amplifier, which are loud enough to use in a nightclub or bar performance.

Guitar amplifiers can also modify an instrument's tone by emphasizing or de-emphasizing certain frequencies, using equalizer controls, which function the same way as the bass and treble knobs on a home stereo, and by adding electronic effects; distortion (also called overdrive) and reverb are commonly available as built-in features. The input of modern guitar amplifiers is a 1/4" jack, which is fed a signal from an electro-magnetic pickup (from an electric guitar) or a piezoelectric pickup (usually from an acoustic guitar) using a patch cord, or a wireless transmitter. For electric guitar players, their choice of amp and the settings they use on the amplifier are a key part of their signature tone or sound. Some guitar players are longtime users of a specific amp brand or model. Guitarists may also use external effects pedals to alter the sound of their tone before the signal reaches the amplifier.

An audio power amplifier (or power amp) amplifies low-power electronic audio signals, such as the signal from a radio receiver or an electric guitar pickup, to a level that is high enough for driving loudspeakers or headphones. Audio power amplifiers are found in all manner of sound systems including sound reinforcement, public address, home audio systems and musical instrument amplifiers like guitar amplifiers. It is the final electronic stage in a typical audio playback chain before the signal is sent to the loudspeakers.

The preceding stages in such a chain are low-power audio amplifiers which perform tasks like pre-amplification of the signal, equalization, mixing different input signals. The inputs can also be any number of audio sources like record players, CD players, digital audio players and cassette players. Most audio power amplifiers require these low-level inputs, which are line level.

In signal processing, a band-stop filter or band-rejection filter is a filter that passes most frequencies unaltered, but attenuates those in a specific range to very low levels. It is the inverse of a band-pass filter. A notch filter is a band-stop filter with a narrow stopband (high Q factor).

Narrow notch filters (optical) are used in Raman spectroscopy, live sound reproduction (public address systems, or PA systems) and in instrument amplifiers (especially amplifiers or preamplifiers for acoustic instruments such as acoustic guitar, mandolin, bass instrument amplifier, etc.) to reduce or prevent audio feedback, while having little noticeable effect on the rest of the frequency spectrum (electronic or software filters). Other names include "band limit filter", "T-notch filter", "band-elimination filter", and "band-reject filter".

An integrated amplifier (pre/main amp) is an electronic device containing an audio preamplifier and power amplifier in one unit, as opposed to separating the two. Most modern audio amplifiers are integrated and have several inputs for devices such as CD players, DVD players, and auxiliary sources.

Vintage integrated amplifiers commonly have dedicated inputs for phonograph, tuner, tape recorder and an auxiliary input. Except for the phono input, all of the inputs are line level, thus, they are interchangeable. The phono stage provides RIAA equalization.

A bass amplifier (also abbreviated to bass amp) is a musical instrument electronic device that uses electrical power to make lower-pitched instruments such as the bass guitar or double bass loud enough to be heard by the performers and audience. Bass amps typically consist of a preamplifier, tone controls, a power amplifier and one or more loudspeakers ("drivers") in a cabinet.

While bass amps share many features with the guitar amplifiers used for electric guitar, they are distinct from other types of amplification systems, due to the particular challenges associated with low-frequency sound reproduction. This distinction affects the design of the loudspeakers, the size and design of the speaker cabinet and the design of the preamplifier and amplifier. Speaker cabinets for bass amps usually incorporate larger loudspeakers (e.g., 15 inches (380 mm) speakers are more common for bass than for electric guitar amps) or more speakers and larger cabinet sizes than those used for the amplification of other instruments. The loudspeakers themselves must also be sturdier to handle the higher power levels and they must be capable of reproducing very low pitches at high sound pressure levels.

An acoustic-electric guitar, also called an electro-acoustic guitar, is an acoustic guitar fitted with a microphone, or a magnetic or piezoelectric pickup. They are used in a variety of music genres where the sound of an acoustic guitar is desired but more volume is required, especially during live performances. The design is distinct from a semi-acoustic guitar, which is an electric guitar with the addition of sound chambers within the guitar body.

Usually, acoustic-electric guitars are fitted with piezoelectric pickups, requiring a preamplifier incorporated into the guitar body to amplify the signal before it travels to the main guitar amplifier. These preamps may also come with an integrated tuner and tone controls of varying types; equalizers with up to six frequency bands may be used.

A keyboard amplifier is a powered electronic amplifier and loudspeaker in a speaker cabinet used for the amplification of electronic keyboard instruments. Keyboard amplifiers are distinct from other types of amplification systems such as guitar amplifiers due to the particular challenges associated with making keyboards sound louder on stage; namely, to provide solid low-frequency sound reproduction for the deep basslines that keyboards can play and crisp high-frequency sound for the high-register notes. Another difference between keyboard amplifiers and guitar/bass amplifiers is that keyboard amps are usually designed with a relatively flat frequency response and low distortion. In contrast, many guitar and bass amp designers purposely make their amplifiers modify the frequency response, typically to "roll-off" very high frequencies, and most rock and blues guitar amps, and since the 1980s and 1990s, even many bass amps are designed to add distortion or overdrive to the instrument tone (for bass, this is called "fuzz bass").

Keyboard amplifiers differ from guitar amplifiers and bass amplifiers in that whereas guitar and bass amps are usually designed for use with one guitar at a time, keyboard amplifiers almost always have a mixer with inputs for two, three, or four keyboards, because many performers often use multiple keyboards. For example, a single player may perform with a stage piano, a keytar and a synthesizer keyboard. Each channel input typically has its own pre-amplifier and volume knob. Keyboard amps in the lower cost range and power output range may only provide equalization controls (for modifying the bass and treble response) for the overall mix. Higher-priced, higher power output keyboard amps designed for professionals may have equalizer controls for each channel. Keyboard amplifiers also differ from guitar amps and bass amps in that whereas many guitar and bass amplifier companies often sell standalone amplifier units (which contain a preamplifier and power amplifier) for use with one or more separate speaker enclosures, keyboard amplifiers are almost always combination (or "combo") amplifiers, so-named because they combine a preamplifier, power amplifier, full-range speaker, and a horn-loaded tweeter, all in a single wooden speaker cabinet.